Manuals Warehouse is your source for copies of owners manuals, service manuals and other documentation on audio, music, stage and studio equipment.

Read/download AER's guitar amplifiers manual and troubleshooting guide. Download by selecting AER Acousticube 3 Amp Owner’s Manual. The second method to troubleshoot is to join in the AER Acousticube 3 Amp discussion and ask your question below. The second method to troubleshoot is to join in the AER Acousticube 3 Amp discussion and ask your question below.

• 3 Operating Instructions, version 1.0 1. Introduction Contents Welcome to AER.

Thank you for purchasing the acoustiCube 3 – without a doubt the benchmark among amplifying systems for acoustic instruments (MIPA Award 2004 for Best Acoustic Intoduction Amp). Contents of Delivery With version “3”. Precautionary Measures When using your acoustiCube 3, always take basic safety precautions to reduce the risk of injury by fire or electric shock to a minimum. Read all the directions in these operating instructions and Should 48/9V phantom power be needed, first establish the make sure that you understand them. Operating Elements Front side, module (from left to right): Channel 2 same as channel 1 clip piezo 48 V clip piezo 48 V input 2 channel channel mute line mute line 2. 1 acoustiCube 3 program mode.

• Risk of electric shock. Insert Do not open. Tuner tuner output without tone control and effects USB-port, connection of the AER DSPs with your phones stereo-headphone output including effects and computer for changing the effect parameters aux-in signal. Use stereo plugs only! • 115/230V ground lift ground lift switch which disconnects signal ground from protective conductor speaker out socket for passive bass box, e.g. AER SUB 12/250P Model:AcoustiCube 3 S/N: 040000097 230/115 V Fuse 3.15 A 4 0 0 0 0 0. • Advice / Problems: acoustiCube 3 with the power switch at the rear of the amp.

Full drive can be achieved at a very low gain level. If the input The green power lamp indicates that the amp is ready for signal is too strong it can be reduced with the pad-switch: if operation. • With the return level you determine the effect level of the internal effect. If the effect is not necessary, set the return level to the zero position (as far left as it will turn). Channel program return acoustiCube 3 effect section Memory Acousticube footswitch. • At the phones output a stereo headphone-amp with max. 2 x 100 mW / 32 Ohms provides you with monitoring possibili- For special AER link function, see the graphics in chapter 10.

Here the direct signal of channel 1 and channel 2 are mo- The link function enables all the signals of the amplifiers no, but the effect parts are stereo. • AER GmbH und Co. D – 45665 Recklinghausen Telephone: +49 (0)23 61–89 17 89 / -90 www.aer-amps.com Copyright: AER, Recklinghausen Telefax: +49 (0)2361 – 891791 AER assumes no liability for printing mistakes. Technical data is subject to alteration after printing. • Revised model with 48V phantom power from 12/1995 Change to Japan-FX-Board (ME-2) with 16 effects From 09/1996 AER Acousticube II with Japan-FX-Board (ME-2/ME-32) New features: 100 effect Three band tone controls Connection for an active subwoofer New power amplifier with output for an ad. • -11- acoustiCube 3 6.

Effect-chart, 1 Reverb Pgr. Description size / time Ambience Pgr. Description size / time Room Room Dark small Glass Room Room Glass Hall Room large Glass Church Room Soft small. • -12- acoustiCube 3 6. Maryland moped license practice. Effect-chart, 2 Special Acoustic Spaces & Outdoor Acoustic Spaces Combinations Pgr.

Description size/time Corridor 1 Warm long Chorus Reverb Corridor 2 Dark long Chorus Reverb bright bright Corridor 3 Bright long Chorus Delay. Wiring Diagrams shield Typical „Insert-lead“ ring e.g. Effect II-Return, Master-Ctrl. Shield sleeve balanced Mic.-lead shield unbalanced Mic.-lead shield ring Stereo-lead (balanced) e.g. Footswitch shield sleeve Mono-lead (unbalanced) e.g.

Instrument shield ring Special AER Insert Cable (look at chapter 10) ring. • -24 dB at 120 Hz BW- = 36 Hz 12 dB noise 5 k Ω (impedance depending on built-in effects AER 32-bit digital effects processor, 'return'. City traffic 3ds max plugin fracture. • -15- acoustiCube 3 9. Signal Flow Diagram, 1. • -16- acoustiCube 3 9.1. Signal Flow Diagram, 2. • -17- acoustiCube 3 10.

Insert Point, AER Link-Function amp 1 amp 2 amp 3 ring line out insert ring return line out external ring effect send aux in insert In case of occupied „return” socket, due to the ring insert operating, you can still loop an external effect, using the effect „send”.